-- *****************************************************************
-- CISCO-CIPCMPC-MIB - This MIB manages the CISCO MultiPath Channel
-- feature on CMCC cards.
--
-- February 1997, Mike Otto
--
-- Copyright (c) 1997-1998, 1999 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-CIPCMPC-MIB DEFINITIONS::=BEGIN
IMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE,Counter32,Integer32FROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
RowStatus,TDomain,TimeStampFROM SNMPv2-TC
ifIndex
FROM RFC1213-MIB
ciscoMgmt
FROM CISCO-SMI
cipCardEntryIndex, cipCardDtrBrdIndex, cipCardSubChannelIndex
FROM CISCO-CHANNEL-MIB
ChannelPath, ChannelDevice
FROM CISCO-CIPCSNA-MIB
ChannelTgName
FROM CISCO-CIPTG-MIB;ciscoCipCmpcMIB MODULE-IDENTITYLAST-UPDATED"9901250000Z"ORGANIZATION"cisco IBU Engineering Working Group"CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"DESCRIPTION"This is the Management Information Base (MIB)
module for objects used to manage the Cisco Multi-Path
Channel (MPC) support on Cisco Mainframe Channel
Connection (CMCC) cards, also called the CMPC feature.
-------------------------------------------------
| Acronym Definitions: |
| CIP = Channel Interface Processor |
| CMPC = Cisco Multi-Path Channel |
| HPR = High Performance Routing |
| HPDT = High Performance Data Transfer |
| ISR = Intermediate Session Routing |
| MPC = Multi-Path Channel |
| MPC+ = HPDT MPC |
| SNA = Systems Network Architecture |
| TG = Transmission Group |
-------------------------------------------------
This MIB consists of the following tables:
1) CMPC Subchannel Administration
2) CMPC Subchannel Operational
3) CMPC TG Statistics
Refer to the following MIBs for an understanding of Cisco
channel terminology and Cisco CMCC terminology:
CISCO-CHANNEL-MIB
CISCO-CIPCSNA-MIB
CISCO-CIPLAN-MIB
CISCO-CIPTG-MIB
"REVISION"9901250000Z"DESCRIPTION"Since the CMCC now supports MPC and MPC+,
the new state, activePlus, was added to
cipCmpcSubChannelOperState to indicate the
TG is active and using the MPC+ protocol."REVISION"9801060000Z"DESCRIPTION"With the addition of Cisco's new Channel Port
Adapter cards, all the references to CIP in the
MIB description and object descriptions are changed
to CMCC (Cisco Mainframe Channel Connection). The
object names in the form of cip... or cipCard...
will remain the same, but will be valid objects
for the Channel Port Adapter cards."REVISION"9702090000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 72}cipCmpcObjects OBJECTIDENTIFIER::={ ciscoCipCmpcMIB 1}cipCmpcSubChannel OBJECTIDENTIFIER::={ cipCmpcObjects 1}cipCmpcTg OBJECTIDENTIFIER::={ cipCmpcObjects 2}-- ;;;;;;;;;;;;;;;;;;;;; cipCmpcSubChannelAdminTable ;;;;;;;;;;;;;;;;;;;;;;;;;;;cipCmpcSubChannelAdminTable OBJECT-TYPESYNTAXSEQUENCEOF CipCmpcSubChannelAdminEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains configuration information used to
define subchannels for the Cisco Multi-Path Channel
(CMPC) feature on the CMCC card.
Each instance of this table is created when a CMPC
sub-channel is configured on the router. When the
CMPC sub-channel configuration statement is deleted
from the router, the instance represented by this
table is removed."::={ cipCmpcSubChannel 1}cipCmpcSubChannelAdminEntry OBJECT-TYPESYNTAX CipCmpcSubChannelAdminEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A list of CMPC configuration values."INDEX{ cipCardEntryIndex,
cipCardDtrBrdIndex,
cipCardSubChannelIndex
}::={ cipCmpcSubChannelAdminTable 1}
CipCmpcSubChannelAdminEntry ::=SEQUENCE{
cipCmpcSubChannelAdminPath ChannelPath,
cipCmpcSubChannelAdminDevice ChannelDevice,
cipCmpcSubChannelAdminTgName ChannelTgName,
cipCmpcSubChannelAdminDirection INTEGER,
cipCmpcSubChannelAdminTgTransport TDomain,
cipCmpcSubChannelAdminRowStatus RowStatus}cipCmpcSubChannelAdminPath OBJECT-TYPESYNTAX ChannelPath
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Channel path for this CMPC instance."::={ cipCmpcSubChannelAdminEntry 1}cipCmpcSubChannelAdminDevice OBJECT-TYPESYNTAX ChannelDevice
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Device address of the subchannel the attached
host will use to communicate with this CMPC
instance."::={ cipCmpcSubChannelAdminEntry 2}cipCmpcSubChannelAdminTgName OBJECT-TYPESYNTAX ChannelTgName
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This is the name of the CMPC transmission group.
Each CMPC subchannel in the same connection
transmission group must have the same TG name"::={ cipCmpcSubChannelAdminEntry 3}cipCmpcSubChannelAdminDirection OBJECT-TYPESYNTAXINTEGER{read (1),
write (2),readOrWrite (3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies whether the CMPC subchannel is for host
reads or host writes."::={ cipCmpcSubChannelAdminEntry 4}cipCmpcSubChannelAdminTgTransport OBJECT-TYPESYNTAXTDomainMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the Transmission Group
transport type OID for which this CMPC Sub-Channel
instance if configured.
When the Transmission Group for this CMPC Sub-Channel
instance is not configured, this object will be set to
the NULL TDomian { 0, 0 }."::={ cipCmpcSubChannelAdminEntry 5}cipCmpcSubChannelAdminRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used by a Management Station to create
or delete the row entry in the cipCmpcSubChannelAdminTable
following the the RowStatus textual convention.
Upon successful creation of the row, an Agent
automatically creates a corresponding entry in
the cipCmpcSubChannelOperTable and
cipCmpcSubChannelStatsTable.
The Management Station can initiate row deletion, by
setting this value to 'destroy (6)'. The Agent will
then delete the rows corresponding to this CMPC
instance from the cipCmpcSubChannelAdminTable,
cipCmpcSubChannelOperTable and cipCmpcSubChannelStatsTable."::={ cipCmpcSubChannelAdminEntry 6}-- ;;;;;;;;;;;;;;;;;;;;; cipCmpcSubChannelOperTable ;;;;;;;;;;;;;;;;;;;;;;;;;;;cipCmpcSubChannelOperTable OBJECT-TYPESYNTAXSEQUENCEOF CipCmpcSubChannelOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains operational information
for the Cisco Multi-Path Channel (CMPC)
feature on the CMCC card."::={ cipCmpcSubChannel 2}cipCmpcSubChannelOperEntry OBJECT-TYPESYNTAX CipCmpcSubChannelOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of CMPC operational and status values. The
entries are created by the Agent. They have
read-only access."AUGMENTS{ cipCmpcSubChannelAdminEntry }::={ cipCmpcSubChannelOperTable 1}
CipCmpcSubChannelOperEntry ::=SEQUENCE
{
cipCmpcSubChannelOperState INTEGER,
cipCmpcSubChannelOperMaxbfru Integer32}cipCmpcSubChannelOperState OBJECT-TYPESYNTAXINTEGER{shutdown (1),inactive (2),xid2Pending (3),active (4),activePlus (5)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Activation state of the CMPC subchannel.
shutdown - CMCC interface with this CMPC
subchannel configured is shutdown.
inactive - CMCC physical channel up, CMPC
subchannel has not started to
activate yet.
xid2Pending - VTAM and CMCC CMPC have started
negotiating channel connection.
active - CMCC CMPC subchannel is active in
MPC or non-HPDT mode.
activePlus - CMCC CMPC subchannel is active in
MPC+ or HPDT mode."::={ cipCmpcSubChannelOperEntry 1}cipCmpcSubChannelOperMaxbfru OBJECT-TYPESYNTAXInteger32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Maximum number of 4096 byte buffers allowed per
channel block I/O on this CMPC subchannel. For host
write subchannels, this is the maximum number of
4096 byte buffers the host can write to the CMCC for
each channel block I/O. Since the CMCC is capable of
receiving 16 4096 byte buffers per channel block I/O,
the value on host write subchannels will always be 16.
For host read subchannels, this is the maximum number
of 4096 byte buffers the host can read from the CMCC
for each channel block I/O."::={ cipCmpcSubChannelOperEntry 2}-- ;;;;;;;;;;;;;;;;;; cipCmpcTgOperTable ;;;;;;;;;;;;;;;;;;;;;;;;cipCmpcTgOperTable OBJECT-TYPE
SYNTAXSEQUENCEOF CipCmpcTgOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains Operational information
for each instance of a CMPC Transmission
Group (TG).
Each instance of this table is created for every
CMPC TG with a unique tg-name configured on a
CMCC card."::={ cipCmpcTg 1}cipCmpcTgOperEntry OBJECT-TYPESYNTAX CipCmpcTgOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"A list of CMPC TG Operational objects."INDEX{ ifIndex,
cipCmpcTgOperName }::={ cipCmpcTgOperTable 1}
CipCmpcTgOperEntry ::=SEQUENCE{
cipCmpcTgOperName ChannelTgName,
cipCmpcTgOperLastSeqNumFailureCause INTEGER,
cipCmpcTgOperLastSeqNumFailureTime TimeStamp,
cipCmpcTgOperExpectedReceiveSeqNum Integer32,
cipCmpcTgOperLastSeqNumReceived Integer32,
cipCmpcTgOperLastSeqNumSent Integer32}cipCmpcTgOperName OBJECT-TYPE
SYNTAX ChannelTgName
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This is the name for this instance of a
CMPC transmission group (TG)."::={ cipCmpcTgOperEntry 1}cipCmpcTgOperLastSeqNumFailureCause OBJECT-TYPESYNTAXINTEGER{none (1),blockSeqError (2),sweepSeqError (3)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The last CMPC TG sequence number failure
cause.
none - No sequence number errors
have been detected.
blockSeqError - Sequence number received
in a cmpc I/O block did not
match the expected sequence
number.
sweepSeqError - Sequence number received in
a sweep message does not compare
to the expected sequence number.
for this CMPC TG."::={ cipCmpcTgOperEntry 2}cipCmpcTgOperLastSeqNumFailureTime OBJECT-TYPESYNTAXTimeStamp
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object describes the value of sysUpTime
when this CMPC TG last detected a sequence
number error. If the CMPC TG has not failed,
then this value shall be zero."::={ cipCmpcTgOperEntry 3}cipCmpcTgOperExpectedReceiveSeqNum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the sequence number expected from the
host by this CMPC TG."::={ cipCmpcTgOperEntry 4}
cipCmpcTgOperLastSeqNumReceived OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the last sequence number received
from the host by this CMPC TG."::={ cipCmpcTgOperEntry 5}cipCmpcTgOperLastSeqNumSent OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the last sequence number sent
to the host by this CMPC TG."
::={ cipCmpcTgOperEntry 6}-- ;;;;;;;;;;;;;;;;;; cipCmpcTgStatsTable ;;;;;;;;;;;;;;;;;;;;;;;;cipCmpcTgStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CipCmpcTgStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains statistical information
for each instance of a CMPC Transmission
Group (TG).
Each instance of this table is created for every CMPC
TG with a unique tg-name configured on a CMCC card."::={ cipCmpcTg 2}cipCmpcTgStatsEntry OBJECT-TYPESYNTAX CipCmpcTgStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of CMPC TG statistical objects."AUGMENTS{ cipCmpcTgOperEntry }::={ cipCmpcTgStatsTable 1}
CipCmpcTgStatsEntry ::=SEQUENCE{
cipCmpcTgStatsConnectReqs Counter32,
cipCmpcTgStatsConnectInds Counter32,
cipCmpcTgStatsConnectRsps Counter32,
cipCmpcTgStatsConnectCnfms Counter32,
cipCmpcTgStatsDiscReqs Counter32,
cipCmpcTgStatsDiscInds Counter32,
cipCmpcTgStatsSweepReqsIn Counter32,
cipCmpcTgStatsSweepReqsOut Counter32,
cipCmpcTgStatsSweepRspsIn Counter32,
cipCmpcTgStatsSweepRspsOut Counter32,
cipCmpcTgStatsWraps Counter32}cipCmpcTgStatsConnectReqs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of connect requests received from
the host by this CMPC TG."
::={ cipCmpcTgStatsEntry 1}cipCmpcTgStatsConnectInds OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of connect indications sent to the
host by this CMPC TG."::={ cipCmpcTgStatsEntry 2}cipCmpcTgStatsConnectRsps OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of connect responses received from
the host by this CMPC TG."::={ cipCmpcTgStatsEntry 3}cipCmpcTgStatsConnectCnfms OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of connect confirms sent to the host
by this CMPC TG."::={ cipCmpcTgStatsEntry 4}cipCmpcTgStatsDiscReqs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Number of disconnect requests received from
the host by this CMPC TG."::={ cipCmpcTgStatsEntry 5}cipCmpcTgStatsDiscInds OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of disconnect Indications sent to the
host by this CMPC TG."::={ cipCmpcTgStatsEntry 6}cipCmpcTgStatsSweepReqsIn OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Number of sweep requests received
from from the host by this CMPC TG."::={ cipCmpcTgStatsEntry 7}cipCmpcTgStatsSweepReqsOut OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of CMPC sweep requests sent by
this CMPC TG."::={ cipCmpcTgStatsEntry 8}cipCmpcTgStatsSweepRspsIn OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Number of CMPC sweep responses received
from VTAM by this CMPC TG."::={ cipCmpcTgStatsEntry 9}cipCmpcTgStatsSweepRspsOut OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of CMPC sweep responses sent by
this CMPC TG."::={ cipCmpcTgStatsEntry 10}cipCmpcTgStatsWraps OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Number of times the CMPC sequence number
for this TG has wrapped."::={ cipCmpcTgStatsEntry 11}--
-- ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
--
-- Notifications
--cipCmpcNotificationPrefix OBJECTIDENTIFIER::={ ciscoCipCmpcMIB 2}cipCmpcNotifications OBJECTIDENTIFIER::={ cipCmpcNotificationPrefix 0}cipCmpcDirectionMismatch NOTIFICATION-TYPEOBJECTS{
cipCmpcSubChannelAdminDirection
}STATUScurrentDESCRIPTION"This trap indicates that the
configured direction for the specified
CMPC subchannel does not match
the direction specified by the host.
The CMPC subchannel will not activate
as long as this mismatch exists."::={ cipCmpcNotifications 1}cipCmpcSeqNumError NOTIFICATION-TYPEOBJECTS{
cipCmpcTgOperLastSeqNumFailureCause,
cipCmpcTgOperExpectedReceiveSeqNum,
cipCmpcTgOperLastSeqNumReceived
}STATUScurrent
DESCRIPTION"This trap indicates that the CMPC
TG has detected an MPC sequence
number error.
This error will cause the CMPC TG
to disconnect."::={ cipCmpcNotifications 2}--
-- ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
--
-- Conformance Information
--ciscoCipCmpcMibConformance OBJECTIDENTIFIER::={ ciscoCipCmpcMIB 3}ciscoCipCmpcMibCompliances OBJECTIDENTIFIER::={ ciscoCipCmpcMibConformance 1}ciscoCipCmpcMibGroups OBJECTIDENTIFIER::={ ciscoCipCmpcMibConformance 2}
--
-- Compliance Statements
--ciscoCipCmpcMibCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for the Cisco Multi-Path
Channel (CMPC) feature."MODULEMANDATORY-GROUPS{
ciscoCipCmpcSubChannelGroup,
ciscoCipCmpcTgGroup
}::={ ciscoCipCmpcMibCompliances 1}ciscoCipCmpcSubChannelGroup OBJECT-GROUPOBJECTS{-- Table Header-- cipCmpcSubChannelAdminTable
-- cipCmpcSubChannelAdminEntry-- Table Header-- cipCmpcSubChannelOperTable-- cipCmpcSubChannelOperEntry-- Table Indicies-- cipCardEntryIndex-- cipCardDtrBrdIndex-- cipCardSubChannelIndex
cipCmpcSubChannelAdminPath,
cipCmpcSubChannelAdminDevice,
cipCmpcSubChannelAdminTgName,
cipCmpcSubChannelAdminDirection,
cipCmpcSubChannelAdminTgTransport,
cipCmpcSubChannelAdminRowStatus,
cipCmpcSubChannelOperState,
cipCmpcSubChannelOperMaxbfru
}
STATUScurrentDESCRIPTION"A collection of objects providing Cisco
Multi-Path Channel (CMPC) Administration,
Operational status and Statistics."::={ ciscoCipCmpcMibGroups 1}ciscoCipCmpcTgGroup OBJECT-GROUPOBJECTS{-- Table Header-- cipCmpcTgOperTable-- cipCmpcTgOperEntry-- Table Header-- cipCmpcTgStatsTable-- cipCmpcTgStatsEntry-- Table Indicies-- ifIndex-- cipCmpcTgOperName
cipCmpcTgOperLastSeqNumFailureCause,
cipCmpcTgOperLastSeqNumFailureTime,
cipCmpcTgOperExpectedReceiveSeqNum,
cipCmpcTgOperLastSeqNumReceived,
cipCmpcTgOperLastSeqNumSent,
cipCmpcTgStatsConnectReqs,
cipCmpcTgStatsConnectInds,
cipCmpcTgStatsConnectRsps,
cipCmpcTgStatsConnectCnfms,
cipCmpcTgStatsDiscReqs,
cipCmpcTgStatsDiscInds,
cipCmpcTgStatsSweepReqsIn,
cipCmpcTgStatsSweepReqsOut,
cipCmpcTgStatsSweepRspsIn,
cipCmpcTgStatsSweepRspsOut,
cipCmpcTgStatsWraps
}STATUScurrent
DESCRIPTION"A collection of objects providing CMPC
TG Operational and Statistical information."::={ ciscoCipCmpcMibGroups 2}END